Stage Ape Lighting Stage Ape Lighting



.

.

.


Home

stage ape lighting
stage ape

stage ape

Read Our Warranty
and Store Policies.

Click Here!
stage ape
stage ape The Ape Blacklight Panel... stage ape
UV LED Flat panel, 192 5mm UV LED’s with very Low power consumption...

Very Low power consumption, Current draw: 30W.

Built-in sound activated and auto programs, master/slave or DMX.

3 channel DMX-512 (Your DMX controller must have a negative polarity switch to run this fixture),

Adjustable flash and speed rate in stand-alone modes, Built-in automated programs via built in mic.

LEDs 100,000hr,  color temp >6000K, 

Size: 14.0" x 9.50" x 3"   Weight: 5.0 lb. Fuse: 2 amp short.
PANEL192UV
stage ape Click Here To Purchase stage ape

Instructions for STAND ALONE operation:

 PANEL192UV

Stand alone mode:

Use the menu, up, down and enter button until the display screen read CL##. Then pick a mode you mode using the up and down button, press enter to set your selection.

CL01 OFF
CL02 10% brightness (in this mode a strobe function can be active, see speed section below)
CL03 30% brightness (in this mode a strobe function can be active, see speed section below)
CL04 40% brightness (in this mode a strobe function can be active, see speed section below)
CL05 50% brightness (in this mode a strobe function can be active, see speed section below)
CL06 60% brightness (in this mode a strobe function can be active, see speed section below)
CL07 80% brightness (in this mode a strobe function can be active, see speed section below)
CL08 100% brightness (in this mode a strobe function can be active, see speed section below)
CL09 Sound active strobe mode 1
CL10 Sound active strobe mode 2
CL11 Sound active strobe mode 3
CL12 Sound active strobe mode 4
CL13 Auto mode 1 (speed can be adjusted, see speed section below)
CL14 Auto mode 2 (speed can be adjusted, see speed section below)
CL15 Auto mode 3 (speed can be adjusted, see speed section below)
CL16 Auto mode 4 (speed can be adjusted, see speed section below)
 

 PANEL192UV

Speed modes:

Speed settings can be accessed in almost every mode in this fixture. Use the up and down buttons to to find SP## on the display. SP01 is for ALL ON mode SP02-SP30 is the speed setting from slow-fast. Make sure to press enter after every mode switch to initiate the program.

To get to an ALL ON mode:

Use the menu, up and down buttons to get to the auto mode CL## on the LED display. Depending on the desired brightness chose from CL02-CL08 going from dim to brightest. Once you have it set on the desired brightness press the ENTER button to set it. Then using the menu, up and down buttons again go to the speed control feature SP## and set that to SP01 and press the ENTER button to set it.

 PANEL192UV

For DMX Mode: 

Use the menu, up and down buttons to get to the DMX mode A### on the LED display. Using the up and down buttons set the DMX value of the fixture and press ENTER.

Channel #1 Strobe
          0-4 No function
          5-63 Strobe speed from slow to fast
          64-68 Sound active strobe
          69-128 Thunder strobe
          129-132 Sound active thunder strobe
          133-192 Gradual fade in (slow-fast)
          193-196 Sound active gradual fade in (slow-fast)
          197-245 Gradual dim (slow-fast)
          246-250 Sound active gradual dim
          251-252 No function

Channel #2  0-255 Dimmer (dim-bright)

Channel #3 Auto mode
          0-5 No function
          6-55 Effect #1
          56-105 Effect #2
          106-155 Effect #3
          156-205 Effect #4
          206-255 Effect #5

How to use this light with the American DJ MyDMX software

PANEL192UV

For MASTER / SLAVE Mode:

Set the master to any auto mode program. Connect the slave fixture to the master via DMX cable. Using the mode, up and down buttons (on the slave units) press until you see SLAE, then press ENTER. 

 cord

Click Here To Purchase

Back

  © 2010 by Stage Ape Lighting