Stage Ape Lighting Stage Ape Lighting

The Lighting you need... at Prices you'll go APE over...


Home

stage ape lighting
     Contact Us:  
     
stage ape
stage ape The Ape PAR 38 LED 86... stage ape
Short, Black LED PAR 38 Can with 86 5mm LED's and a 35 Degree Beam Angle...

This LED PAR 38 can puts out 1,277 LUX at 1 meter. (A standard PAR 38 can with a 150 watt halogen bulb and a primary blue color gel in front of it puts out 99 Lux at 1 meter).

44 red, 21 green, 21 blue LED’s.

Soft edge spot. Built in mic.

5 channel dmx: #1=on/off and strobe, #2=dimmer, #3=Red #4=Green #5=Blue

Stand alone modes features: Sound active with built in mic and sensitivity knob, auto color change and master/slave mode.

Color temp less than 6000k. Includes 1 amp short fuse, 100,000 hour LED’s. Under 13 watt current draw.

Size 4.75" x 4.75" x 3.5" and weighs 1.7Lbs
 led cans

stage ape Click Here To Purchase stage ape

Instructions for STAND ALONE operation:

 side led 86 can
With only dip switch #1 on (up), the Red LED's come on at approximately 50%

With only dip switch #2 on (up), the Red LED's come on at approximately 50%

With only dip switch #1 & #2 on (up), the Red LED's come on at approximately 100%

With only dip switch #3 on (up), the Green LED's come on at approximately 50%

With only dip switch #4 on (up), the Green LED's come on at approximately 50%

With only dip switch #3 & #4 on (up), the Green LED's come on at approximately 100%

With only dip switch #5 on (up), the Blue LED's come on at approximately 50%

With only dip switch #6 on (up), the Blue LED's come on at approximately 50%

With only dip switch #5 & #6 on (up), the Blue LED's come on at approximately 100% 		 front led 86 can
With only dip switch #9 on (up), full brightness, fast color change.

With only dip switch #9 & #7 on (up), full brightness, slow color change.

With only dip switch #8 on (up), full brightness, sound active color change.		 side led 86 can
DMX mode:

The 120-LED-86 is a 5 channel dmx light so you start DMX value 1. Set dip switches #1 & # 10 on the first fixture to the on position. Dip switch 10 is on to tell the light it is in DMX mode and does not have a value. This will allow the first 5 sliders on your controller to control the first light.  So now set the next fixture at dmx value 6 which is dip switches #2 & #3 & #10 to the on position. This will allow you to us sliders 6 through 10 to control the second fixture.

On your DMX controller:
Slider #1 is:
    0-15 = Off
    16-79 = Strobe, slow to fast
    80-159= Pulse strobe (fades out and back to bright, slow to fast)
    160-255 = On
Slider #2- Brightness, low to high (controls overall brightness).
Slider #3- Brightness of the red LED’s
Slider #4- Brightness of the green LED’s
Slider #5- Brightness of the blue LED’s

How to use this light with the American DJ MyDMX software		 back led 86 can

Master/Slave:


Set dip switches #1-8 on the master fixture to the "On" position. Connect the second fixture by DMX cord.
Then set dip switch #10 of the slave fixture to the "On" position. 

120-LED86

Click Here To Purchase

Back


 Copyright 2009 by Stage Ape Lighting